Polishing liquid glass with your hands: the process of technology

polishing of car body liquid glass

Every car enthusiast strives to ensure that his vehicle always look well kept and clean. To achieve a similar result of modern polishing compound. Not so long ago on the shelves of the store were only the classical tools. But today the most popular polishing with liquid glass.

What this means

Polishing liquid glass is carried out with a particular base composition. This colour is made on the basis of silicate of sodium or potassium. The production of the material is made by melting quartz sand with soda. The result of this treatment is a high-quality composition and at the same time a safe product designed to restore gloss on the vehicle.

What you need

Polishing liquid glass requires preparation of the vehicle. However, before beginning such work, it is recommended to check out the full set of shades. Along with this tool, which are sold the following tools:

  • the base composition and curing agent;
  • with the pipette you can easily mix the ingredients;
  • special fibres designed for manual polishing;
  • protective gloves;
  • soft sponge;
  • towel.

If there is a tool that is recommended to buy it separately. Otherwise, carefully Polish the body will not work.

Preparation of the vehicle

Preparation of the vehicle

For polishing the car with liquid glass, which is successful, it is good to prepare the body. To start:

  1. Thoroughly wash the vehicle to remove any dirt, dust and insects.
  2. Area of the body must be well degreased. For these purposes, it is advisable to use white spirit, diluted in clean water. Should not be used for degreasing refers to a composition that contains low-quality alcohols or silicones. After processing the car must be dry.
  3. If, before the use of liquid glass body was covered in the Polish, it should be removed completely. Otherwise the new coating will be very bad to stay on the surface of the body. This greatly shorten its life.

If you hold the polishing

Car polishing liquid of the glass must be on a small platform. The place must be dry, well-ventilated. In operation, the temperature should be 10-40 degrees above zero. Experts recommend that the Polish body in the garage. If the procedure will be carried out on the street, in the car, put under the canopy.

When applied to a special composition on the surface of the body, you must avoid getting on the car, dirt, dust, and direct sunlight.

What you need to take into account

Polishing of car body liquid glass is a time-consuming process. If you are a beginner in business, it is worth considering a few simple rules. In the first place, not used, specially formulated for the whole body. Should be covered with a small first piece. This will allow you to assess how the liquid glass respects the surface of the vehicle. If you get the expected result, you can safely proceed to the polishing of the entire vehicle.

It is also worth considering, that is used to make the body gradually, the treatment section by section. For example, you can start with the bumper and finish the roof. When one part of the vehicle, which will be processed in full, you can start polishing the next one. This approach is necessary for two reasons. So the treatment of the body, will be made more effective. In addition, the Polish will not dry quickly.

How to apply liquid glass

What you need to take into account

Polishing liquid glass, it is necessary to start with the preparation of a special composition. Before mixing the components, which is carefully studied the instructions for use, and to perform everything as indicated. Otherwise, poland will prove to the bad. When the composition is ready, you can start using at the surface of the body. In this case it is necessary to proceed very carefully.

Every part of the body should apply a small amount of Polish, and then grind all with a soft cloth, which should be included. In carrying out such work should ensure that the surface retains the dust. Once fully treat the entire body, it is necessary to leave the vehicle only for about six hours. The cover is a little dry.

It should be noted that full hardening of the liquid glass takes place on day 14 after application. In this period, it is not recommended to wash the vehicle, especially at the car wash. After the surface is completely protected from moisture, sun, salt and other problems.

Is it possible to speed up the process

As is the time required for the polishing liquid of the glass? Reviews from owners suggest that the whole process of the body, while doing great work, which takes about 6 hours. Many can't survive so long. so, the question arises whether it is possible to speed up the polishing process? A simplification to use additional tools, such as grinding machine. While polishing, you should pick up a soft polishing pad. Is made using liquid glass only on medium speed. Put extra stress on the grinding machine for polishing is not recommended. Otherwise, the surface will begin to overheat.

If there is no sander, then for work, you can use an electric drill equipped with a special attachment for fixing the lap for polishing.

How much will it cost

Polishing liquid glass with their own hands is much cheaper than polished in the showroom. It is worth noting that the price of the quality of the products is 3-6 thousand rubles. Of course, the cost of liquid glass, which is much higher than the normal nails. However, this coating is much more. Use the same liquid glass does not require special tools and special skills. And this, in turn allows you to save money.

At the end of the

Is it possible to speed up the process

After the polishing of the body with the liquid glass forms a smooth and neat finish. The vehicle, which becomes more and more well-groomed look. If necessary, this coating can be upgraded. It should be noted that the liquid glass is based on the body surface in a period of one year. The coating can withstand up to 50 visits to a specialized car wash. In addition, for the care of the body, which requires only a clean cloth and a bottle of water.

Polishing liquid glass in the home - this is real. The most important thing is to stock up on all the necessary tools and patience. Then you can get a job.

09.08.2018